|
| Our Products  Spray-On Equipment |
   |
 |
|
We handle the full line of Glas-Craft products. |
| Super Maxi
The Glas-Craft Super Maxi Dispensing System is designed for economical use in small to medium polyurea output applications. The Super Maxi may also be used for higher output foam insulation, as well as pour foams. A 50-foot heated hose assembly is standard on the Super Maxi unit. | |
Click on the equipment picture to view Adobe PDF brochures. |
 |
Specifications:
• Max Output: 18 lb per min / 8.2 kg per min
• Max Temp: 190º F / 88º C
• Primary Heaters: 6000 Watts
• Max Pressure: 2200/3000 PSI, 150/204 Bar
• Hose Size: 1/4” i.d. / 64 mm
• Length: 35 ft. Std / 210 Ft Max
• Heat: Super Heat Tape
• Heat Control: Solid-state LED Control
• Material Feed: Transfer Pumps
• Probler Gun: Round Spray 17254-xx or P2 23950-xxElectrical Requirements:
50 amp, 208-240 VAC, single phase, 50/60 Hz Air Requirements:
47 cfm @100 psi / 1330 l/min @ 6.8 bar |
|
|
Glas-Craft MH
The MH can generate 3000 psi fluid pressure and necessary material
temperature to spray most all polyurea and polyurethane coatings.
Generating fluid pressure and maintaining that pressure while spraying –
are two different matters.
The MH is the top of the line polyurethane/polyurea machine for the
industrial applications and is a lower air consumption unit. Large fluid
section pumps 1 gallon in 16 strokes and has a capacity to pump over 5
gallons per minute. It relies on a hydraulic motor instead of a
pneumatic motor. A 50-foot heated hose assembly is standard on the MH unit. |
 |
Specifications:
• Max Output: 45 lb per min / 20 kg per
min
• Max Temp: 190º F / 88º
C
• Primary Heaters:
14,000 Watts (7000 watts per side)
• Max Pressure: 3000
PSI, 190 Bar
• Hose Size: 3/8” i.d. / 95 mm
• Length: 50 ft. Std / 300 Ft Max
• Heat: Copper-wound Hoses
• Heat Control: Solid-state LED Control
• Material Feed: Transfer Pumps
• Probler Gun: Round Spray 17254-xx or P2 23950-xx
Electrical Requirements:
Three Phase 208 VAC - 63AMP 60 Hz Three Phase
380 VAC - 63AMP 50 Hz Air Requirements:
15 cfm@100 psi 425 l/min@6.8 bar |
| |
| Glas-Craft MH II
The MH II can generate 2500 psi fluid pressure and necessary material temperature to spray most all polyurea and polyurethane coatings. Generating fluid pressure and maintaining that pressure while spraying – are two different matters.
The MH II will have a very low pressure drop when you pull the trigger –
giving you the require mixing pressure at the gun where needed – not
just static pressure. | |
 | Specifications:
• Max Output: 22 lb per min / 10 kg per min
• Max Temp: 190º F / 88º C
• Primary Heaters: 6000 Watts
• Max Pressure: 2200/3000 PSI, 150/204 Bar
• Hose Size: 3/8” i.d. / 95 mm
• Length: 50 ft. Std / 300 Ft Max
• Heat: Copper-wound Hoses
• Heat Control: Solid-state LED Control
• Material Feed: Transfer Pumps
• Probler Gun: Round Spray 17254-xx or P2 23950-xxElectrical Requirements:
74 amp / 208/240 V VAC AC Single Phase Phase, , 60 Hz 40 amp / 208/240 V VAC AC Three Phase Phase, , 60 Hz 40 amp / 380 V VAC AC Three Phase Phase, , 50 Hz Air Requirements:
15 cfm@100 psi 425 l/min@6.8 bar |
|
Glas-Craft MH III
The Glas-Craft MH III Dispensing System is a hydraulically driven system, designed for use in house or in a field location. The MH III is the top of the line polyurethane/polyurea machine for the bedliner and is a lower air consumption unit. It relies on a hydraulic motor instead of a pneumatic motor. A 50-foot heated hose assembly is standard on the MH III unit. | |
 |
Specifications:
• Max Output: 22 lb per min / 10 kg per min
• Max Temp: 190º F / 88º C
• Primary Heaters: 10000 Watts
• Max Pressure: 3000 PSI / 204 Bar
• Hose Size: 3/8” i.d. / 95 mm
• Length: 50 ft. Std / 310 Ft Max
• Length: 10 ft. Heated Whip
• Heat: Copper-wound Hoses
• Heat Control: Solid-state LED Control
• Material Feed: Transfer Pumps
• Probler Gun: Round Spray 17254-xx or P2 23950-xxElectrical Requirements:
74 amp, 208-240 VAC, single phase, 60Hz.
50 amp, 208-240 VAC, three phase, 60Hz.
40 amp, 380 VAC, three phase 50/60 Hz. Air Requirements:
15 cfm @100 psi / 425 l/min @ 6.8 bar |
|
Guardian A6
The Guardian A6 Dispensing System is a pneumatic system, designed
for use in house or in a field location. The Guardian A6 is the top of the line polyurea machine for the bedliner
and industrial applications. The design of the Guardian air motor
delivers efficient, consistent trouble free operation. The Guardian
A6 comes from the factory with the Probler P2 gun, 50-foot heated
hose and 10' whip and is capable of handling up to 310' of total
hose. |
|
 |
Specifications:
• Max Output: 20 lb per min / 9 kg per min
• Max Temp: 190º F / 88º C
• Primary Heaters:
1. A6-6000 - 300 Watts per side (6000 watts total heat)
2. A6-12000 - 6000 Watts per side (12000 watts total heat)
• Max Pressure: 2200 / 3000 PSI
• Hose Size: 3/8” i.d. / 95 mm
• Length: 50 ft. Std / 310 Ft Max
• Length: 10 ft. Heated Whip
• Heat: Copper-wound Hoses
• Heat Control: Digital Controllers for Iso, Poly & Hose heat
• Material Feed: Transfer Pumps
• Gun: Round Spray Probler P2 23950-xx
Electrical Requirements
A6-6000
50amp 220 VAC, single phase, 50 / 60Hz 25 amp, 220 VAC, three phase, 50 / 60Hz.
25 amp, 380 VAC, three phase 50/60 Hz.
A6-12000 75
amp, 220 VAC, single phase, 50 / 60Hz.
35 amp, 208-240 VAC, three phase,
50 / 60Hz.
35 amp, 380 VAC, three phase 50/60 Hz.
Air Requirements:
33 cfm @100 psi /
834 l/min @ 6.8 bar (Includes transfer pumps) |
|
Probler Gun
Reliable... That's the proven Probler Gun. Rugged construction with fewer wear parts means a light-weight (three pounds), maneuverable gun that's tough on the job and easy on the operator. Continuous air purge eliminates sticking valve rods and associated downtime... No more constant triggering. Since the gun cannot be operated without the air purge being activated, an operator can stop, pick-up and start spraying again without danger of setting up the gun. Pistol-grip handle and full finger trigger have been designed to fit the hand for easy, comfortable spraying. | |
 | Versatile... The Probler spray gun adapts to most proportioners, so you can upgrade your existing equipment by simply connecting a Probler Gun to assure proper mixing and maximum yield. And what's more, Probler simplifies your entire spray operation and saves you time and money because it's the one gun that covers all output ranges. With Probler, the one gun that does it all, you don't have to worry about several guns and an inventory of spare parts for each. Probler Gun Features:
• Angled hose connections
• Air shut-off valve
• Consistent spray pattern
• Air-actuated spray pattern
• Mixing chambers: round or flat spray
• Side block check valve assemblies
• Manual material shut-off valves
• High pressure airless mixing |
| 
 The next generation in plural component spray guns Probler P² is here! Place your order NOW! Lightweight, Ergonomic Design Compact design makes it easy for operators to maneuver into difficult spray positions. Hardened Metal Mixing Chamber & Side Block Seals Longest lasting seals available. Two Piece Mixing Chamber If a drill bit breaks off in the mixing chamber, you just replace the inexpensive snout - not the entire chamber. Check Valve Separating Liquid Portion of Gun from Dry Areas No more cleaning small air passages with tiny drill bits. Dual Air Piston for Double the Triggering Force Over 300 psi of trigger force - you will not see sluggish chamber movement when you pull the trigger. Grease Fitting on the Gun for Daily Lubrication You don't need to take the gun apart for daily service. Individual Side Block Attachment to Gun. You will not need to line everything up or have a third hand to get side blocks attached to the gun Minimal Daily or Routine Maintenance Required You don't need to take the gun apart daily - or even weekly. Probler P² can be used with either harden steel or standard plastic side block seals. The New Probler P² Features: ● Smaller, lighter weight, & easier to use ● Better spray pattern ● Less overspray ● New duel piston air cylinder ● New two piece mixing chamber ● Fluid screens on both A and B side blocks ● steel side wipe seal option ● Grease fitting on the gun head ● New look
|
|
Back To Top |
|
|
